北京仁华工程技术有限公司
Beijing Ranvor Engineering Co.,Ltd
型号:HSK/L 430x0.7 mm





Special characteristics of this HSK shear:
Ø All electrical and pneumatic interfaces are connected inside 2 junction boxes, so as to adapt to the requirement of fully automatic system.
Ø Shearing pressure: 0- 40KN, adjustable;
Ø Shearing angles:1, 2, 3 degrees, adjustable;
Ø Shearing gap: 0.02mm-0.2mm;
Ø Strength of shearing samples: 300MPa-700MPa;
Ø Shearing speed: 120 times/minute, no less than 20 Epstein sets per hour (each 24 strips for one set)
Ø Sample size after cutting:320×30±0.1mm,burr less than 5um.
Ø Overall work efficiency: the time for completing the whole process of cutting a batch of 40 serial numbers is no more than 30 minutes (The sample sheet of each serial number includes 2 big sheets, with a maximum shearing of 32 pieces);
Ø Failure rate: continuous operation for 72 hours, the failure does not exceed 2 times, and the failure time does not exceed 5 minutes.
Ø The hardness of the shearing blade HRC is greater than 65, the blade flatness error does not exceed 5um, and the blade base flatness error does not exceed 5um.
本款HSK剪板机特点:
Ø 所有电气和气动接口均连接在2个接线盒内,以适应全自动系统的要求;
Ø 剪切力:0- 40KN,可调
Ø 剪切角度:1、2、3度可调
Ø 剪切间隙:0.02mm-0.2mm
Ø 剪切试样强度:300MPa-700MPa
Ø 剪切速度:每分钟剪切次数120次,每小时不少于20套爱泼斯坦试样(每套试样24片);
Ø 剪切的试样尺寸精度要求:320×30±0.1mm,毛刺小于5um;
Ø 整体作业效率:完成一次批量40个序号的样板剪切全流程时间不超过30分钟(每个序号的样板包括2块大样,最多共剪切32片);
Ø 故障率:连续72小时运行,故障不超过2次,每次故障时间不超过5分钟;
Ø 剪切刀片的硬度HRC大于65以上,刀片平整度误差不超过5um,刀片基座平整度误差不超过5um;
Main technical specifications of this HSK shear该剪板机主要技术参数:
The high-performance punching and shearing machine is equipped with a high-precision positioning system to ensure the smallest sample burrs after punching.
Shearing machine model: HSK/L 430x0.7
Shearing machine weight: 600kg
Power supply: 3x380V±10%, 6kw
Drive motor model: SEW KAF 77 CM3C80M-30A-P/BZ/PK/RH1M/SB1 (with resolver and brake)
Maximum motor speed: 150 r/min
Shear angle: 0.38°
The fastest cycle time of the blade: 0,6 s
Maximum cutting times in single stroke mode: 30
Maximum shear force: 42.5kN
Spindle torque: 358Nm
Maximum tensile strength: 1150 N/mm²
Cutting thickness: 0.1 mm -0.7 mm
Maximum cutting width: 430mm
Cutting angle adjustment range: 0.38 degrees, with stroke of cutter bar 18 mm, opening 13 mm
Blade size: 450 x 50 x 10 mm, 4 blades of 90°
Lubricating oil tank: 5L
Electromagnetic influence: less than 0.02% influence on magnetic performance after shearing.
高性能冲剪机配有高精度定位系统,确保冲剪后样品毛刺最小。
剪板机型号:HSK/L 430x0.7
剪板机重量:600kg
电源:3x380V±10%,6kw
驱动电机型号:SEW KAF 77 CM3C80M-30A-P/BZ/PK/RH1M/SB1(带旋转变压器和制动器)
电机最大转速:150 r/min
剪切角度:0.38°, 刀杆行程18mm,开口13mm
刀片最快循环时间:0,6 s
单冲程模式下最大剪切次数:30
最大剪切力:42.5kN
主轴扭矩:358Nm
最大抗拉强度:1150 N/mm²
剪切厚度:0.1 mm -0.7 mm
最大剪切宽度:430mm
剪切角度调整范围:0.38度
刀片尺寸:450 x 50 x 10 mm,4个90°刀面
润滑油箱:5L
电磁影响:剪切后对磁性能影响小于0.02%
Other technical specifications of this HSK shear本款剪板机其它技术参数:
- standard cast iron side frame
- welded shear table covered with 10 mm plastic plates with additional grooves for a gripper system
(WITHOUT additional support arms under the plastic plates)
- table height approx. 780 mm
- hold down mounted close to the cutting area, with rubber cord glued in a slot at the bottom side,
spring-actuated and linked with the movement of the cutter bar
- automatic oil central lubrication, brand SKF/Vogel, with pressure and liquid level switch, 24 V DC, realized with piston distributors
- blades manufactured in one piece with
4x90° wedge angle
- upper and lower blade with dimensions
450 x 50 x 10 mm with threaded bores M10
- adjustable cam disc on main shaft and non-contact inductive proximity switch for referencing the servo drive
- additional non-contact proximity switch for control of upper dead center of the cutter bar, both sensors brand SICK
- milled surfaces at both side frames for exact adjustment of the machine
- manual cut gap adjustment with fine threaded spindles for adjusting the cut gap after turning or changing the blades
- oil collect pans under main shaft and eccentrics
with oil drain plugs
(mounted at the inner side of the side frames)
- manually pluggable security bolt for avoiding
the cutter bar moving downwards if machine is disconnected from energy supply
(without additional monitoring)
- with scrap chute at the backside
- WITHOUT: motor-driven front stop
with gripper
- WITHOUT: electrical control/circuit
- WITHOUT: cable, servo amplifier, terminal box
- WITHOUT: start-up of the servo motor
(we use a conventional bevel gear motor for testing the machine during start-up)
- WITHOUT: additional security devices
- side of central lubrication: RIGHT
- side of motor: LEFT
- color: shear RAL 7035 grey
- moving parts RAL 2003 orange
motor black RAL 9005 (SEW standard)
- documentation in English language (1x printed, 1x on CD)
- 标准铸铁侧板机架
- 焊接式剪切工作台,台面覆 10 mm 厚塑料板,板上预留夹持装置专用凹槽
(塑料板下方无附加支撑臂)
- 工作台高度:约 780 mm
- 压料机构紧邻剪切区布置;压料底面开槽内嵌橡胶密封条,弹簧驱动,与刀架联动
- SKF/Vogel 品牌自动集中稀油润滑系统,配置压力开关、液位开关,DC24V,配活塞分配器
- 一体式刀片,四面刃口,楔角 90°
- 上、下刀片规格:450×50×10 mm,带 M12?→M10 螺纹安装孔
- 主轴配可调凸轮盘,搭配非接触式电感接近开关,用于伺服驱动回零定位
- 增设非接触式接近开关,用于检测刀架上止点;两只传感器均为 SICK 品牌
- 两侧机架设有铣削基准面,用于设备精准调校
- 剪切间隙手动调节机构,配细牙调节丝杆,用于刀片翻面或更换后的间隙调整
- 主轴、偏心轮下方设有带放油螺塞的集油盘
(安装于侧板机架内侧)
- 可手动插拔式安全销:设备断电时锁住刀架,防止刀架意外下行
(不带状态监控功能)
- 机身背部配置废料滑槽
- 不含:带夹持机构的电机驱动前挡料
- 不含:电控系统、控制回路
- 不含:电缆、伺服驱动器、接线盒
- 不含:伺服电机调试启动服务(出厂试机采用常规锥齿轮电机进行设备测试)
- 不含:额外安全防护装置
- 集中润滑布置侧:右侧
- 电机布置侧:左侧
- 涂装:剪板机主体 RAL 7035 浅灰
运动件 RAL 2003 橙黄
电机黑色 RAL 9005(SEW 原厂标准色)
- 随机资料:英文版(纸质版 1 份 + CD 光盘版 1 份)