北京仁华工程技术有限公司
Beijing Ranvor Engineering Co.,Ltd
型号: HSK/N 1380 x 1 mm




Very fast motor-driven guillotine shear HSK/N 1380 x 1 mm at 400 N/mm² tensile strength
with unique direct drive system with fly-wheel and pneumatically actuated clutch-brake-combination with minimal wearing of the clutch AND with reduced cutting angle for minimal torsion of cut strips
-RPM in idle mode approx. 160 1/min.
-thus start-stop-time approx. 60 s / 160 + 0,15 s = 0,525 s in single stroke mode
-machine used only in single stroke mode
-drive by AC-motor with 2,2 kW
-stroke of cutter bar 50 mm
-opening of blades (left side) approx. 25 mm
-overlapping of blades (right side) approx. 3 mm
-thus cutting anlge 0,9°
-angle of action approx. 180°
-thus cutting time approx. 0,1875 s
-opening of hold down approx. 4 mm
-weigh approx. 1.250 kg (rough estimation)
抗拉强度 400 N/mm² 工况下,HSK/N 1380×1 mm 型高速电机驱动闸式剪板机
配置独特的飞轮直驱系统 + 气动离合制动组合单元,离合器磨损低;采用减小剪切角设计,最大限度降低裁切条料的扭曲变形。
- 空程转速:约 160 r/min
- 单行程模式单次启停周期:60÷160+0.15 s = 0.525 s
- 本机仅采用单行程模式工作
- 驱动:2.2 kW 交流电机
- 刀架行程:50 mm
- 刀片(左侧)开启量:约 25 mm
- 刀片(右侧)重叠量:约 3 mm
- 剪切角:0.9°
- 作用角:约 180°
- 剪切耗时:约 0.1875 s
- 压料装置开启量:约 4 mm
- 设备自重:约 1250 kg(估算值)
Special characteristics of this HSK shear:
With the following standard and special equipment:
-vibration damping cast iron side frames
-precise guidance of the cutter bar, additionally covered with sliding plastics to realize failsafe running functions
-machine control mounted fix at the outer side of the left side frame
-shear table manufactured in one piece with flat steel surface
-manually actuated central lubrication realized with piston distributors (has to be acutated every 8 hours)
-oil collect pans with oil drain plugs mounted under eccentrics and main bearings
-hold down manufactured in one piece pneumatically actuated to realize earlier clamping and therfore to increase accuracy of cutting using the backstop; mounted close to the cutting area
-sidewise stop at the left side of the shear table with measuing tape, length 1.000 mm
-two table extensions at the front side of the shear table mounted at fix positions, length 650 mm (without additional T-slots but with plain surface)
-motor-driven back stop in robust design realized with gear rods, frequency converter and AC-motor, accuracy 0,1 mm, lengths 600 mm, realized with one axis positioning control, type P40, brand ELGO
-pneumatically actuated tilting table realized with rolls as sheet metal support at the back side of the machine, with special mechanics which allow the tilting table to be shifted 100 mm away form the cutting area so that smaller strips can be cut faster without sheet metal support; guillotine shear broadened in order to realize this special mechanics
-with sheet metal chute under the tilting table which is used when tilting table is shifted away from the lower blade
-shear blades manufactured in one piece with four cutting edges with 90° wedge angle, 1400 x 60 x 12 mm with threaded bores M12
-manuall cut gap adjustment with fine threaded spindles at the left and right front side of the machine; shear table with lower blade permanently clamped by four screws and disc spring packages at the outer side of the side frames;
with additional mechanical measuring clockworks for precise adjustment if needed
-cut realese by electrical foot switch
-sidewise safety guards at the backside of the machine according to DIN EN 13985 "safety plate shears", combined with safety light barrier at the end of the safety guards
-with precision wegde shoes for easier and vibration damping adjustment of the shear, screw-on type (packed with the machine, not mounted)
-coloring machine signal grey RAL 7004 and moving parts maize yellow RAL 1006
本款 HSK 剪板机专项特性:
标配及专项配置如下:
- 减振式铸铁侧板机架
- 刀架精密导向结构,导向面镶嵌耐磨滑动塑料,保障设备安全可靠运行
- 机床控制柜固定安装于左侧机架外侧
- 一体式剪切工作台,工作台面为平整钢板
- 手动集中润滑系统,配活塞分配器(润滑操作每 8 小时执行一次)
- 偏心轮、主轴承下方设置带放油螺塞的集油盘
- 一体式气动压料机构,可提前压紧板材,配合后挡料提升裁切精度;布置于剪切区域近旁
- 剪切工作台左侧侧向定位挡块,附带 1000 mm 长标尺
- 工作台前端固定安装两组工作台延伸托板,单块长度 650 mm;板面为光面,无附加 T 型槽
- 电机驱动后挡料,结构坚固,由齿轮丝杆、变频器、交流电机组成;定位精度 0.1 mm,行程 600 mm;ELGO 品牌 P40 型单轴定位控制系统
- 机身后侧气动翻板托料台,台面配辊轴支撑板材;专属机械结构可将翻板托料台向远离剪切区方向移出 100 mm,裁切窄条料时可撤去板材支撑、提升裁切效率;机身加宽结构为适配该专项机构
- 翻板托料台下方配置落料滑槽,用于托料台移出下刀刃后的出料
- 一体式剪切刀片,四面可用刃口,楔角 90°;刀片尺寸 1400×60×12 mm,预开 M12 螺纹安装孔
- 剪切间隙手动调节:机床左右前侧配置细牙调节丝杆;工作台下刀由 4 组螺栓 + 机架外侧碟簧组件持续压紧;按需可选配机械百分表,实现间隙精调
- 剪切动作由电动脚踏开关控制
- 机身后侧侧向安全防护,符合 DIN EN 13985《剪板机安全标准》;防护端部配套安全光栅
- 配套精密楔式调平垫块,便于机床调平、减振;螺栓固定式(随机发货,出厂不预装)
- 涂装:机身主体为信号灰 RAL 7004,运动件为玉米黄 RAL 1006