北京仁华工程技术有限公司

Beijing Ranvor Engineering Co.,Ltd

产品中心
自动爱泼斯坦方圈检测线,剪板机单机设备
    发布时间: 2026-10-27 14:05    

型号:HSK/L 430x0.7 mm


自动爱泼斯坦方圈检测线,剪板机单机设备

Special characteristics of this HSK shear:

 

Ø All electrical and pneumatic interfaces are connected inside 2 junction boxes, so as to adapt to the requirement of fully automatic system.

Ø Shearing pressure: 0- 40KN, adjustable;

Ø Shearing angles:1, 2, 3 degrees, adjustable;

Ø Shearing gap: 0.02mm-0.2mm;

Ø Strength of shearing samples: 300MPa-700MPa;

Ø Shearing speed: 120 times/minute, no less than 20 Epstein sets per hour (each 24 strips for one set)

Ø Sample size after cutting:320×30±0.1mm,burr less than 5um.

Ø Overall work efficiency: the time for completing the whole process of cutting a batch of 40 serial numbers is no more than 30 minutes (The sample sheet of each serial number includes 2 big sheets, with a maximum shearing of 32 pieces);

Ø Failure rate: continuous operation for 72 hours, the failure does not exceed 2 times, and the failure time does not exceed 5 minutes.

Ø The hardness of the shearing blade HRC is greater than 65, the blade flatness error does not exceed 5um, and the blade base flatness error does not exceed 5um.

 

本款HSK剪板机特点:

 

Ø 所有电气和气动接口均连接在2个接线盒内,以适应全自动系统的要求;

Ø 剪切力:0- 40KN,可调

Ø 剪切角度:1、2、3度可调

Ø 剪切间隙:0.02mm-0.2mm

Ø 剪切试样强度:300MPa-700MPa

Ø 剪切速度:每分钟剪切次数120次,每小时不少于20套爱泼斯坦试样(每套试样24片);

Ø 剪切的试样尺寸精度要求:320×30±0.1mm,毛刺小于5um;

Ø 整体作业效率:完成一次批量40个序号的样板剪切全流程时间不超过30分钟(每个序号的样板包括2块大样,最多共剪切32片);

Ø 故障率:连续72小时运行,故障不超过2次,每次故障时间不超过5分钟;

Ø 剪切刀片的硬度HRC大于65以上,刀片平整度误差不超过5um,刀片基座平整度误差不超过5um;

 

Main technical specifications of this HSK shear该剪板机主要技术参数:

 

The high-performance punching and shearing machine is equipped with a high-precision positioning system to ensure the smallest sample burrs after punching.

Shearing machine model: HSK/L 430x0.7

Shearing machine weight: 600kg

Power supply: 3x380V±10%, 6kw

Drive motor model: SEW KAF 77 CM3C80M-30A-P/BZ/PK/RH1M/SB1 (with resolver and brake)

Maximum motor speed: 150 r/min

Shear angle: 0.38°

The fastest cycle time of the blade: 0,6 s

Maximum cutting times in single stroke mode: 30

Maximum shear force: 42.5kN

Spindle torque: 358Nm

Maximum tensile strength: 1150 N/mm²

Cutting thickness: 0.1 mm -0.7 mm

Maximum cutting width: 430mm

Cutting angle adjustment range: 0.38 degrees, with stroke of cutter bar 18 mm, opening 13 mm

 

 

Blade size: 450 x 50 x 10 mm, 4 blades of 90°

Lubricating oil tank: 5L

Electromagnetic influence: less than 0.02% influence on magnetic performance after shearing.

高性能冲剪机配有高精度定位系统,确保冲剪后样品毛刺最小。

剪板机型号:HSK/L 430x0.7

剪板机重量:600kg

电源:3x380V±10%,6kw

驱动电机型号:SEW KAF 77 CM3C80M-30A-P/BZ/PK/RH1M/SB1(带旋转变压器和制动器)

电机最大转速:150 r/min

剪切角度:0.38°, 刀杆行程18mm,开口13mm

刀片最快循环时间:0,6 s

单冲程模式下最大剪切次数:30

最大剪切力:42.5kN

主轴扭矩:358Nm

最大抗拉强度:1150 N/mm²

剪切厚度:0.1 mm -0.7 mm

最大剪切宽度:430mm

剪切角度调整范围:0.38度

刀片尺寸:450 x 50 x 10 mm,4个90°刀面

润滑油箱:5L

电磁影响:剪切后对磁性能影响小于0.02%

 

Other technical specifications of this HSK shear本款剪板机其它技术参数:

 

- standard cast iron side frame

- welded shear table covered with 10 mm plastic plates with additional grooves for a gripper system

(WITHOUT additional support arms under the plastic plates)

- table height approx. 780 mm

- hold down mounted close to the cutting area, with rubber cord glued in a slot at the bottom side,

spring-actuated and linked with the movement of the cutter bar

- automatic oil central lubrication, brand SKF/Vogel, with pressure and liquid level switch, 24 V DC, realized with piston distributors

- blades manufactured in one piece with

4x90° wedge angle

- upper and lower blade with dimensions

450 x 50 x 10 mm with threaded bores M10

- adjustable cam disc on main shaft and non-contact inductive proximity switch for referencing the servo drive

- additional non-contact proximity switch for control of upper dead center of the cutter bar, both sensors brand SICK

- milled surfaces at both side frames for exact adjustment of the machine

- manual cut gap adjustment with fine threaded spindles for adjusting the cut gap after turning or changing the blades

- oil collect pans under main shaft and eccentrics

with oil drain plugs

(mounted at the inner side of the side frames)

- manually pluggable security bolt for avoiding

the cutter bar moving downwards if machine is disconnected from energy supply

(without additional monitoring)

- with scrap chute at the backside

- WITHOUT: motor-driven front stop

with gripper

- WITHOUT: electrical control/circuit

- WITHOUT: cable, servo amplifier, terminal box

- WITHOUT: start-up of the servo motor

(we use a conventional bevel gear motor for testing the machine during start-up)

- WITHOUT: additional security devices

- side of central lubrication: RIGHT

- side of motor: LEFT

- color: shear RAL 7035 grey

- moving parts RAL 2003 orange

motor black RAL 9005 (SEW standard)

- documentation in English language (1x printed, 1x on CD)

- 标准铸铁侧板机架

- 焊接式剪切工作台,台面覆 10 mm 厚塑料板,板上预留夹持装置专用凹槽

(塑料板下方无附加支撑臂)

- 工作台高度:约 780 mm

- 压料机构紧邻剪切区布置;压料底面开槽内嵌橡胶密封条,弹簧驱动,与刀架联动

- SKF/Vogel 品牌自动集中稀油润滑系统,配置压力开关、液位开关,DC24V,配活塞分配器

- 一体式刀片,四面刃口,楔角 90°

- 上、下刀片规格:450×50×10 mm,带 M12?→M10 螺纹安装孔

- 主轴配可调凸轮盘,搭配非接触式电感接近开关,用于伺服驱动回零定位

- 增设非接触式接近开关,用于检测刀架上止点;两只传感器均为 SICK 品牌

- 两侧机架设有铣削基准面,用于设备精准调校

- 剪切间隙手动调节机构,配细牙调节丝杆,用于刀片翻面或更换后的间隙调整

- 主轴、偏心轮下方设有带放油螺塞的集油盘

(安装于侧板机架内侧)

- 可手动插拔式安全销:设备断电时锁住刀架,防止刀架意外下行

(不带状态监控功能)

- 机身背部配置废料滑槽

- 不含:带夹持机构的电机驱动前挡料

- 不含:电控系统、控制回路

- 不含:电缆、伺服驱动器、接线盒

- 不含:伺服电机调试启动服务(出厂试机采用常规锥齿轮电机进行设备测试)

- 不含:额外安全防护装置

- 集中润滑布置侧:右侧

- 电机布置侧:左侧

- 涂装:剪板机主体 RAL 7035 浅灰

     运动件 RAL 2003 橙黄

     电机黑色 RAL 9005(SEW 原厂标准色)

- 随机资料:英文版(纸质版 1 份 + CD 光盘版 1 份)