北京仁华工程技术有限公司

Beijing Ranvor Engineering Co.,Ltd

产品中心
A型HSK闸式剪板机
    发布时间: 2026-10-27 13:50    

型号:HSK/G 1230 x 1.2 mm 

A型HSK闸式剪板机

Motor-driven guillotine shear HSK/G 1230 x 1,2 mm at 700 N/mm² tensile strength


with reduced cutting angle (1,33°)to realize a fine-cutting shear especially for cutting thin sheet metal with minimum torsion of cut sheet metal strips

-Drive by geared motor with brake power 3,0 kW

-RPM of geared motor approx. 65 1/min.

-Cylce time approx. 1,1 s

-Weight approx. 1.150 kg


电动闸式剪板机 HSK/G 1230×1.2 mm,适配板材抗拉强度 700 N/mm²。

本机采用小剪切角设计(1.33°),属于精剪型剪板机,尤其适合薄板剪切,可最大限度减小剪切条料的扭曲变形。

- 驱动:带制动齿轮电机,功率 3.0 kW

- 齿轮电机转速:约 65 r/min

- 单次循环时间:约 1.1 s

- 设备重量:约 1150 kg



Special characteristics of this HSK shear:


-Vibration damping cast iron side frames

-Very precise guidance of the cutter bar for cutting thin sheet metal

-Guidance of the cutter bar additionally covered with sliding plastics for realizing emergency running properties

-Cutter bar precisely fitted, surface-gauged and manually shaved

-Cutter bar realized with calculated crown bow

-Very long-lasting contruction with constant precision


本款HSK剪板机特点:


- 减振铸铁侧板

- 刀座导向精度高,适配薄板剪切工况

- 刀座导向副加装自润滑滑动塑料层,具备应急干运转能力

- 刀座精密配磨、面检并经手工刮研处理

- 刀座按计算值加工预拱挠度

- 结构耐用,长期使用精度稳定


With the following technical specification:


-Shear table manufactured in one piece with plain steel surface, height 770 mm plus height of round shoes (see below)

-Hold down manufactured in one piece with rubber cord glued in a slot at the bottom side; pneumatically actuated so that movement of the hold down is NOT linked with the movement of the cutter bar and can be individually adjusted - also the hold down pressure

-Cutting illumination integrated in the cover of the guillotine shear for possible cutting by marks on the sheet metal

-Sidewise table stop with measuring tape mounted at the left side of the shear table, length 600 mm

-Two table extensions, length 450 mm, with plain surface (without T-slot) mounted at fix positions at the front side of the shear table

-Manually actuated oil-central lubrication realized with piston distributors

-Motor-driven back stop with fully-automatic positioning control brand ELGO, electronic piece counter and pneumatically actuated sleeve clamping, length 600 mm

-Special sheet metal support by pneumatically actuated tilting table with rolls and chute to the backside of the machine

-Blades manufactured in one piece using special blade steel, dimensions 50 x 12 x 1250 mm with threaded bores M10

-Manual cut gap adjustment with thread spindles at the front side of the left and right side frame, manual clamping with screws at the external side of both side frames; for adjusting the cut gap after changing or turning the blades

-Cut release by movable foot switch

-Sidewise protection guard ending directly behind the back stop for a compact machine design, height 1600 mm

-Light curtain mounted at the backside of the machine

-Machine used only in single stroke mode

-Vibriation damping round shoes for comfortable and precise adjustment of the machine and better ergonomics by increasing the height of the shear table (not mounted, but delivered separately)

-Coloring: machine signal grey RAL 7004; contrast color maize yellow RAL 1006 


技术参数和配置:


- 剪切台整体加工,普通钢台面;台面基准高度 770 mm(不含调平垫脚,见下文)

- 压料板整体结构,底部槽内镶嵌橡胶压条;气动驱动,压料动作与刀座剪切动作相互独立,压料行程、压料力均可单独调节

- 剪切标线照明灯集成于剪板机机罩内,可按板材划线定位剪切

- 工作台侧挡料(带卷尺),安装于剪切台左侧,量程 600 mm

- 2 块工作台延伸托板,单块长 450 mm,光面无 T 型槽,固定安装于剪切台前端

- 手动集中稀油润滑系统,配活塞式分配器

- 电动后挡料,ELGO 品牌全自动定位控制系统,带电子计件功能、气动套筒夹紧,挡料行程 600 mm

- 专用薄板托料装置:气动翻板托料台,带输送辊与出料溜槽,布置于设备后侧

- 整体式刀片,专用刃口钢材,规格 50×12×1250 mm,配 M10 螺纹安装孔

- 剪隙手动调节:左右侧板前端设调节丝杆,侧板外侧螺钉锁紧;刀片更换 / 翻面后用于调整剪切间隙

- 剪切启动:移动式脚踏开关

- 侧防护栏止于后挡料后方,结构紧凑,防护高度 1600 mm

- 安全光幕安装于设备后侧

- 设备工作模式:仅单行程剪切

- 减振调平垫脚:方便设备精准调平,抬高台面优化操作人机工程(垫脚随货单独发货,出厂不预装)

- 涂装颜色:主机信号灰 RAL 7004;标识对比色玉米黄 RAL 1006




Shear blades as spare parts

consisting of upper and lower blade dimensions 50 x 12 x 1250 mm with threaded bores M10

剪切刀片可选作为备件,上下刀片尺寸为50 x 12 x 1250mm,螺纹孔为M10。